Label printers SQUIX UHF RFID
Highest reliability in processes related to writing and printing RFID labels

Direct thermal printing requires less pressure exterted to a print head, resulting in a longer life cycle of the latter.

if operating label rolls with a core diameter of 100 mm and outside diameter succeeds 180 mm

2.4 GHz 802.11b/g/n
Hotspot mode or infrastructure mode

to extend the range of operation
2.4 GHz 802.11b/g/n + 5 GHz 802.11a/n/ac
Hotspot mode or infrastructure mode

for use with materials guided aligned to the left or in centered position

The moveable sensor qualifies for small or customized labels. As soon as a label has been removed, the next one is automatically printed.

The minimum width of a label in use is 4 mm, its minimum height 6 mm.

If materials are in use aligned to the left, they must be 12 cm to 60 mm distant to the locating edge. Materials in centered position: ibid

for use with labels that hardly separate due to strong adhesive or thick liner material. Use only if printing has been triggered by the touch of a button on the display or by a control signal. A present sensor cannot be used.

Detecting products automatically on a conveyor

Labeling is triggered via a PLC, a sensor or a hand switch. Status reports and errors are displayed.

All control signals connect to the I/O interface using clamping screws.

A maximum of 16 labels per box can be selected from a memory card by a superior control unit, such as a PLC. Two boxes may be plugged. Making use of an I/O box, four inputs and four outputs suffice for implementing PLC processes via abc programming.

For plugging to a digital I/O interface

For plugging to a digital I/O interface

9/9 pins, 3 m

are provided assembled to a printer ex factory or accessorial on delivery for all SQUIX 4 units.

Paper labels and self-adhesive labels, cardboard and synthetic materials can be cut, so can shrink tubes. By pivoting the cutter, materials can be accessed for removal.

The CSQ 402 provides a more powerful engine and titanium-coating, enabling highly performant cutting even with thick materials such as cardboard and shrink tubes, as well as with self-adhesive materials. The number of cuts performed are kept in memory, allowing wear control.

* at use of material 1 mm high, no backfeed

are provided for all SQUIX 4M units
Continuous materials such as shrink tubes can be perforated, to simplify separation by hand at a later stage.

The design and technical data correspond to the CSQ 402.

*at use of material 1 mm high, no backfeed

Paper labels and self-adhesive labels, cardboard, textile and synthetic materials can be cut, so can shrink tubes.

Tray for collecting a maximum of approximately 50 labels

* at use of material 1 mm high, no backfeed

Continuous materials such as textiles or shrink tubes can be perforated, to simplify separation by hand at a later stage. Cutting a material is as well possible.

* at use of material 1 mm high, no backfeed

for detecting linear 1D barcodes, 2D and stacked codes

A camera checks a code printed on a label in horizontal or vertical direction in terms of legibility or content. In the case of a bad coding, printing stops and the label can be removed by hand. Retracting such labels after stopping and blackening them is another printer option.

The scanner can be operated in tear-off mode and in peel-off mode.

 See www.cab.de/en/cc200 for more information.

1 Printed materials can be cut and then collected. Print jobs stop if the maximum number of labels have been collected. Limitations may occur with stiff or curved materials. cab recommends to have such operations tested.

2 A unit can be set anywhere on a table with the help of a base frame.

* at use of material 1 mm high, no backfeed

 
Support table - label W x H
The table and the protective cover adapt to the label size. To be requested individually.

enable labels be rewound internally on peel-off units. A guide plate therefore replaces the peel-off plate.

for printer assembly using screws

Label webs wound outside or inside are wound consistently and tight by electronic control, with the help of a pendulum arm.

Label webs wound outside or inside are wound consistently and tight by electronic control, with the help of a pendulum arm. They operate also with printers other than cab.

External rewinder	ER4/300	ER6/300
Operated with	SQUIX 4.3 SQUIX 4 SQUIX 4.3 M SQUIX 4 M	SQUIX 6.3
Material width mm max.	120	180
Roll diameter mm max.	300
Core diameter mm	40 if a winder axle or a cardboard core are in use 76 if a cardboard core is in use with an adapter
Winding	outside or inside
6.5 Adapter kit

Even heavy rolls are fed consistently.
Label webs wound outside or inside can be operated.

External unwinder	EU4/300		EU6/300
Operated with	SQUIX 4.3 SQUIX 4	SQUIX 4.3 M SQUIX 4 M SQUIX 4.3 MT SQUIX 4 MT	SQUIX 6.3
Material width mm max.	120	114	180
Roll diameter mm max.	300
Core diameter mm	38.1
Core diameter mm if an adapter is in use	76
Winding	outside or inside
6.5 Adapter kit

Apply labels in real time
S1000 attached to a SQUIX peel-off printer is economic, whether operated semi-automated or integrated in vertical orientation to a manufacture plant. Labels are applied to an item by a stroke cylinder.

1 Long life cycles: The ball bearing guide bars are low wear.

2 Different levels of application: By providing different lengths of stroke for the cylinder, labels can be applied on various heights to an item.

3 Compressed air regulation: Micro filters prevent from contamination. Decompression keeps the quality of label applications consistently high.

4 Reliable processes: Supporting air, intake air and stroke speeds can all be set. The pressing force can be reduced to less than 10N (1kg) in sensitive operations. Purging the intake ducts subsequent to every label application prevents from contamination.

5 A wide range of sizes: Labels 25 mm to 176 mm wide and 25 mm to 200 mm high can be applied.

6 Supporting air: It enables labels be blown onto a pad.

7 Pad: Labels are transferred to a pad and held there by vacuum. A stroke cylinder moves the pad with the labels to an item.

Pre-dispense
Label applications can be verified by the touch of a button. Printing is triggered on a first touch and the printed label is transferred to the applicator. The label is applied on a second touch.

1) calculated at a stroke of 100 mm below a unit, using labels 100 mm high and a print speed of 100 mm/s

Drilled intake holes arranged in a grid are covered by foil. Piercing according to the size of a label

They are manufactured according to the size of a label.

Universal pads, spring-mounted
Pitch of spring enables labels be applied even to inclined surfaces. Drilled intake holes arranged in a grid are covered by foil. Piercing according to the size of a label

Tamp pads, spring-mounted
Pitch of spring enables labels be applied even to inclined surfaces. They are manufactured according to the size of a label.

They suit for items sensitive to pressure.
The pad locates approx. 10 mm ahead of an item.

Labels are fed to below a roller subsequent to printing. The pad moves onto an item. Labels are carried along by the item and rolled on.

Apply labels in real time
S3200 attached to a SQUIX peel-off printer is economic, whether operated semi-automated or integrated to a manufacture plant. Printed labels are set 45° to 95° to the horizontal by a rotary cylinder and applied automatically to an item by a short stroke cylinder.

Life cycles, pre-dispense, compressed air regulation, reliable processes and supporting air correspond to S1000.

1. calculated using labels 40 mm high and a print speed of 100 mm/s

Tamp-on pads or blow-on pads
They are manufactured according to the size of a label.

Cylindric items can be labeled on a 360° circumference. They are placed onto rollers. Label applications are triggered by a hand switch or a foot switch.

A mount and a cable for plugging a SQUIX printer are included on delivery, so is a foot switch.

A label printer system and a jig for retaining an item can be assembled.

1 Assembly plate: to assemble a label printer system

2 Profile, aluminum square: 40 mm, 80 mm, 120 mm. Further lengths may be provided upon request.

3 Base plate: to assemble a jig for retaining an item, Standard size 500 mm x 255 mm

Floor stand
It enables a printer system be ready quickly and flexibly in any manufacture plant. Target positions (i.e. heights, widths) to apply a label can be set in few steps. Four guide rollers provide mobility. At the place of operation, the floor stand can be aligned with the help of feet to adjust.

Jig to retain a printer unit
A printer can be fixed to the assembly plate and quick-locked.

provided for SQUIX 2, SQUIX 4, SQUIX 6

Manufactured according to DIN EN 61340-5-1:2016 to protect from electrostatic charge

The hinged cover, top plate included, is also a spare part.

provided for SQUIX 4, SQUIX 6

By means of a magnetic cover, splints can be detected by metal detectors or x-ray inspection systems.

Blue color optically differentiates from food.

The entire casing can be manufactured detectable upon request.

Materials comply with food directives such as EU Nr. 10/2011 and FDA CFR 21 177.2600

provided for SQUIX 4, SQUIX 6

Labels are removed through an aperture on the front.

The front cover must be opened and the printer pulled out on telescopic rails for material replacement. Steam jet cleaning only if the entire unit is closed.

Protection class IP69K according to EN 60529