Accessories for Label printer XC4
-
Extras
-
Print roller DR4S
Material width up to 120 mm
Silicone coating for an extra long service life at a higher imprint tolerance -
Memory Card
CompactFlash Type I
-
External operation panel
If the operation panel is no longer accessible after the printer has been installed in a plant, an external one can be additionally added. A slot to connect a CF memory card Type I as well as a host interface are provided.
-
-
Interfaces
-
Label selection – I/O box
Up to 16 labels per box can be selected from the memory card by a master control, e.g. PLC. Two boxes can be connected. The I/O box allows simple PLC control processes with four inputs and outputs each via abc programming.
-
WLAN 802.11b/g
Only few cards left in stock. After the remainder has been sold out, no repeat orders are possible.
-
-
Cutting, perforating, stacking labels
-
Cutter CU
Paper labels, self-adhesive labels, cardboard, textile and plastic materials as well as shrink tubes can be cut.
Cutter CU4 CU6 CU8 Usage XD4T, XC4 XC6 A8+ Material width up to mm 110 180 232 Material weight cardbaord gr/m2 60 - 300 Material thickness mm 0.05 - 0.8 Cutting length from mm 5 Gap height up to mm 2.5 Cuts/min, without material up to 100 Stop print job when final cutter position not attained -
Perforation cutter PCU4
Continuous materials such as textiles or shrink tubes are perforated before they are manually separated. In addition, the materials can also be cut.
Perforation cutter PCU4 To be used with XD4T, XC4 Perforating Web distance mm 0.5 Perforating Web width mm 2.5 or 10 Material width up to mm 85 Material weight cardbaord gr/m2 60-300 Material thichness mm 0.05 - 0.8 Cutting length from mm 5 Gap height up to mm 2.5 Cuts/min. without material up to 100 Stop print job when final cutter position not attained -
Stacker ST4 with cutter
The printed materials are cut and stacked. If the maximum stack height is reached, printing is interrupted. Limitations may apply to stiff or curved materials. We recommend to have these materials tested at our premise.
Stacker with cutter ST4 L ST4 M To be used with XC4 XD4T Material width up to mm 20-110 20-100 Material weight cardboard gr/m2 60-300 Material thickness mm 0.05-0.8 Cutting length mm 20-150 Gap height up to mm 1.2 Cuts/min, without material up to 100 Stop print job when final cutter position not attained,
stacker cover open, stack height attainedStack height up to mm 100 Storage table label W x H
The support table and the protective cover are adapted to the label size. They have to be ordered separately.
-
-
Connecting cables
-
Connecting cable RS232-C
9/9 pin, length 3 m
-
-
Rewinding labels
-
External rewinders ER4/6/8
with built-in power supply units. To be used also with external printers. Label winding outside or inside.
External rewinder ER4/210 ER4/300 ER6/300 ER8/300 To be used with XD4T, XC4 XD4T, XC4 XC6 A8+ Material width up to mm 120 120 180 235 Roll diameter up to mm 205 300 300 300 Core diameter mm 40 in cases of a rewind axle or a cardboard core
76 in cases of a cardboard core and an adapterWinding outside or inside Power supply 100–240 V ~ 50/60 Hz Adapter kit for 6.3 ER8 with A8+ 6.4 ER4, ER6 with XC4, XC6
-
-
Software
-
Label software cablabel S3
In cablabel S3 cab concentrates label design, print control and monitoring of all cab marking systems and synchronizes the development of devices and software.
-
Database Connector
In the stand-alone mode with additional network connection, the Database Connector enables printers to access data directly from a central ODBC-, OLEDB compatible database and to print it as a label.
-
Administration Network Manager
The cab Network Manager enables the user to control a number of printers across a network simultaneously. It supports monitoring, configuration, firmware updates, memory card administration, file synchronization and PIN administration centrally.
-
Programmer's guide
A general programmer's guide explaining and describing commands for different printer models via direct programming.
Programming Manual
Programming Manual A+ Series, XD4T, MACH4, PX and all printing systems based on the cab „X2“ board
-