They are attached to the two mounting rods. The path of a label web can be aligned even during labeling
using an extender 3.

For better operation or when space is limited, a labeling head may be installed rotated in vertical direction. Applying labels then requires a dispenser tongue continuously adjustable from -10° to 100°.

When labeling insert onto curved surfaces, demand modules may adapt to the surfaces and heights of items by spring force.
Pivoting heights can be adjusted from 10 mm to 80 mm.
Use requires a wipe-down roller.

upon request

The dispenser tongue can be pivoted electrically when dealing with sensitive surfaces, when labeling onto cylindrical items or into pockets.
Pivoting heights are 10 mm to 20 mm.
Use requires a wipe-down roller.

upon request

A wipe-down roller can be pivoted electrically when dealing with sensitive surfaces, when labeling onto cylindrical items or into pockets.
Pivoting heights as high as 10 mm

A Carriages
The carriage is installed on the guide of a demand module.

Three-part adjustment of wipe-down roller:
1 Distance 5 mm to 40 mm to a peel-off plate
2 Lower end position of roller to an item
3 Wipe-down force onto an item by spring preload

B AR wipe-down rollers
Material: open-cell foam for standard applications
The roller is installed on the lever.
It can be replaced without tools when worn.

C ARS wipe-down rollers
Material: FDA approved silicone
10 times longer service life compared to open-cell foam
Suitable for food applications and clean rooms
The roller is installed on the lever.
It can be replaced without tools when worn.

A Carriage
The carriage is installed on the guide of a demand module.

Three-part adjustment of wipe-down brush:
1 Distance 1 mm to 35 mm to a peel-off plate
2 Height to a peel-off plate
3 Angle of 15° to 45°

B AB wipe-down brushes
Use with standard labels at least 20 mm wide and 20 mm high. The brush is installed directly on the carriage using a square shaft. It can be replaced without tools when worn.

Material: stainless steel, diameter 16 mm
They are assembled both to the profiles of a demand module and a labeling head.

Further lenghts upon request

Assembly of IXOR peel-off plates and wipe-down rollers
Dimension D is adjusted to C using a QP cross-section profile and MS 25 mounting rods.

A third MS mounting rod and further QP cross-section profiles may be added for reinforcing long mounting rods or attaching accessories.

Lengths of mounting rods as required

It is connected to the labeling head via a smart communication interface. Teaching is performed on the operation panel. Entire calibration takes just two labels.

A ceramic probe inductively detects the difference in height from a liner to the top of a label. The sensor can be aligned along the retainer bar. Distances can be easily set using a scale.

Retainer bar
It is adjustable for accurate spotting after sensor disassembly.

Stop
Three lengths are provided. It is assembled
in conjunction with a stop onto the dispenser tongue.
Distance A is optimized for wipe-down rollers and brushes.

Assembled onto a demand module Sensor distances to the locating edge are 7.5 mm to 17.5 mm

Assembled onto a retainer
Sensor distances to the locating edge are 8.0 mm to 40 mm.

Retainer for assembly at any spot to mounting rods, fixed by screws

Dispensing a label is triggered as soon as an item has been detected. 200 mm maximum detectable track

Cable M12-M8, 5 pins, a-coded, 2.5 m included

Incremental, resolution 0.1 mm, tracked A and B
Connecting cable M12, 5 pins, a-coded, 2.5 m
for automatically synchronizing the speed of labeling

Unlocked by key

Circumference 200 mm, diameter 63.7 mm

It presses a friction wheel by spring force onto a conveyor.
Assembly to a conveyor requires a mounting bracket.

Same functionality as on a labeling headunit

Users are free to decide whether to operate
an external panel or the one integral to a dispenser.

1 USB slot, transmitting configuration or firmware transfer

2 LED: Power ON

1.8 m, 3 m, 5 m (11 m upon request)

Plugged to a labeling head

Red: Collective error, e.g. label web ending, broken liner
Yellow: Prior warning to a label web ending
Green: Unit ready

Connecting USB cable included, 1 m

M12, 17 pin, lengths 5 m

M12, 17 pins, 2.5 m, 10 m

Cable plug M12, 5 pins, a-coded, male
Circular connector to base unit START, PRINT & APPLY, STOP

Cable jack M12, 5 pins, a-coded, female
Circular connector to base unit SYNC

The product sensor and the rotary encoder each are provided once for both labeling heads. Signals are transmitted to both labeling heads via a distributor.

Distributor M12, 5 pins, a-coded:
1 x female → 2 x male for a product sensor
1 x male → 2 x female for a rotary encoder

Ethernet connection requires a RJ45 adapter.

Assembly of a labeling head to a base plate or a conveyor
Position setting using a hand crank

It is assembled to the column stand guide. Another column stand is attached to it rotatable in perpendicular direction. Adjustable angles are 0° to 45°

Primarily suggested when applying labels from the top.
As a mobile tool, it can be locked and set on-site by leveling feet.

	1632 Floor stand
Leveling feetadjustable by mm	± 15
Loadkg max.	50
Load at offset 300 mmkg max.	25
Distance from lower margin of a label to the floormm	880 - 1,200
Column stand 600
Adjustable trackmm	595
Weightkg approx.	40

Primarily for labeling from the side on a product. It is adjustable in height and can be locked and set with the help of leveling feet on site.

	1231 Floor stand
Leveling feet, adjustabilityby mm	± 15
Loadkg max.	50
Load at offset 200 mm max. kg	20
Distance from lower label margin to the floormm	664 - 904
Column stand 600
Column length mm	600
Adjustable track mm	395
Tie rod
Unit retainer fine adjustable
Dimension of adjustability mm	135
Weightkg approx.	40