SQUIX 貼標手臂
可建置於生產線上

貼標手臂 S1000

cab Etikettendrucker SQUIX mit Applikator S1000

即印即貼應用
針對所有具備剝離功能的條碼印表機，貼標手臂 S1000 搭配條碼印表機 SQUIX 是相當經濟實惠的解決方案 - 不僅可半自動操作也能垂直建置於生產線上。藉由舉升氣缸將標籤貼在產品上。

貼標手臂	S1000-220	S1000-300	S1000-400
應用機型	SQUIX 2, SQUIX 4.3, SQUIX 4, SQUIX 4.3 M, SQUIX 4 M, SQUIX 6.3
行程長度 mm	220	300	400
可壓貼距離 mm	64	144	244
運作氣壓值 bar	4.5
貼標速度¹⁾	25 貼標循次數/分

1) 由 100 mm 的可壓貼距離、標籤高度 100 mm、列印速度 100 mm/s 所計算得出

貼標手臂 S3200

即印即貼應用
針對所有具備剝離功能的條碼印表機，貼標手臂 S3200 搭配條碼印表機 SQUIX 是相當經濟實惠的解決方案 - 不僅可半自動操作也能建置於生產線上。可將列印完成的標籤自動貼標於產品上。

藉由旋轉氣缸手臂可在 45° - 95° 的區間水平轉動定位標籤，並藉由短行程氣缸將標籤貼在產品上。

cab Etikettendrucker SQUIX mit Applikator S3200

vergrößern

使用壽命、預先剝離功能、氣壓計、穩定度和支撐氣流等說明請參照貼標手臂 S1000。

貼標手臂	S3200
應用機型	SQUIX 2, SQUIX 4.3, SQUIX 4, SQUIX 4.3 M, SQUIX 4 M
氣缸旋轉角度	45°- 95°
最大行程長度 mm	30
運作氣壓值 bar	4.5
貼標速度¹⁾	20 貼標循次數/分

由標籤高度 40 mm、列印速度 100 mm/s 所計算得出

壓貼墊片或吹貼墊片可依照標籤大小訂製。

	壓貼墊片			吹貼墊片
	A3200-1100		M3200-1100	A3200-2100		M3200-2100
出紙方向	靠左		置中	靠左		置中
應用機型	SQUIX 2	SQUIX 4.3, 4	SQUIX 4.3 M, 4 M	SQUIX 2	SQUIX 4.3, 4	SQUIX 4.3 M, 4 M
標籤寬度 mm	4-63	10-116	4-110	10-63	10-116	10-110
標籤高度 mm	6-80			10-80
產品表面	平面
產品位置	靜止			靜止或直線移動

滾貼模組 S5104, S5106

應用於輸送帶上的產品貼標。感應器偵測到貼標位置後開始列印程序，貼標進行的同時同步列印下一張標籤。傳送速度和列印速度必須保持一致。使用反射式感應器監控定位。

cab Etikettendrucker SQUIX mit Spendemodul S5104

vergrößern

滾貼模組	S5104	S5106
應用機型	SQUIX 4.3, SQUIX 4	SQUIX 6.3
出紙方向	靠左
標籤寬度 mm	25-116	50-176
標籤高度 mm	25-210
列印位置到剝離板距離 mm	336-518
產品表面	平面
產品高度	固定
產品位置	直線移動、條碼印表機同速動作
貼標速度¹⁾	60 貼標循次數/分

由標籤高度 100 mm、列印速度 100 mm/s 所計算得出

cab 非常樂意在任何時候、任何地點為您解答任何疑問：

條碼印表機 SQUIX 專用貼標手臂

現在就提出免費及非強制性購買的詢價需求：

詢問更多訊息

更多資訊：

參閱產品目錄(PDF)

貼標手臂 S1000

1 產品使用壽命長：氣缸採用滾珠軸承，耐磨損。

2 適用於不同產品高度：舉升氣缸可依不同高度進行貼標。提供訂購不同的行程長度。

3 氣壓計：微型過濾器能過濾髒污，減壓閥則確保標籤維持良好的列印品質。

4 高穩定度：支撐氣流、吸附氣流和氣缸的舉升速度都可調整。針對易碎產品和包裝能將接觸壓力調至小於 10 N ( 1 kg )。
為了避免在吸氣管道累積髒污，在完成每次貼標動作後會利用空氣壓力脈衝清潔。

5 標籤尺寸：適用於寬度 25 - 176 mm、高度 25 - 200 mm 的標籤。

6 支撐氣流：支撐氣流可輔助固定標籤於墊片上。

預先剝離按鈕
應用於測試貼標程序。確定作業後開始列印標籤並由貼標手臂吸標、貼標。按下開始鈕後可重新進行貼標程序。

cab 非常樂意在任何時候、任何地點為您解答任何疑問：

條碼印表機 SQUIX 專用貼標手臂

現在就提出免費及非強制性購買的詢價需求：

詢問更多訊息

更多資訊：

參閱產品目錄(PDF)

手冊文件

全部顯示全部關閉

產品目錄

名稱	格式	版本	上次更新	語言
工業型條碼印表機 SQUIX	PDF - 4.99 MB	09/2019	2019/09/06	繁體字

註冊是必要的

請先填寫以下表格及正確的EMAIL信箱

您將會收到EMAIL通知，其中提供了下載的連結。

名字 *

姓氏 *

電子郵件 *

cab Produkttechnik GmbH & Co KG  (hereafter "cab") or its affiliated companies hereby grants you a non-exclusive, nontransferable license at no charge to use these 3-D models and the corresponding documentation according to the following terms:
LICENSE GRANT  -  You may
- install the 3-D models on your personal computers;
- use and transmit the 3-D models on a network within a site;
- make copies of the 3-D models in machine readable form for backup purposes;
- modify the 3-D models in connection with your projects
- pass on the models to third parties in connection with your projects

LICENSE RESTRICTIONS  -  You may not:
- rent, sell, transfer or grant any rights in the 3-D models or corresponding documentation without the prior, explicit written consent of cab;
- remove any proprietary notices, labels, or marks on the 3-D models and corresponding documentation;
- make accessible to the public
- market the 3-D models as part of a product or service

NATURE OF THIS AGREEMENT  -  This license is not a sale. Provided that you pay license fees they are in consideration of the licenses granted under this Agreement. Title and copyrights to the 3-D models, corresponding documentation, and any copy made by you, remain the property of cab or its suppliers.  Failure to comply with the above restrictions shall automatically terminate this license without further notice and terminate your rights to use the 3-D models and cab shall, in addition to its other legal remedies, be entitled to its reasonable attorney fees.
LIMITED WARRANTY  - The 3-D models were compiled with great care and checked for accuracy. However cab can not guarantee that all data is up to date, correct and complete. Short-term technical changes are possible at any time. CAD software should only be used by trained staff. It is not a substitute for specialized testing and assessment. cab is not responsible for results on basis of these 3-D models. cab's entire liability and your exclusive remedy under this warranty will be, at the option of cab, to attempt to correct or help you around errors, to replace the 3-D models with functionally equivalent 3-D models, or to terminate this Agreement.
EXCEPT FOR THE ABOVE EXPRESS LIMITED WARRANTY, CAB MAKES AND YOU RECEIVE NO WARRANTIES, EXPLICIT, IMPLIED, STATUTORY OR IN ANY COMMUNICATION WITH YOU, AND CAB SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  CAB DOES NOT WARRANT THAT THE OPERATION OF THE PROGRAM WILL BE UNINTERRUPTED OR ERROR FREE.
Some states do not allow the exclusion of implied warranties so the above exclusions may not apply to you.  This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
LIMITATION OF LIABILITY  -   IN NO EVENT WILL CAB BE LIABLE FOR ANY DAMAGES, INCLUDING LOSS OF DATA, WHILE LOADING THESE 3-D MODELS OR OTHERWISE, LOST PROFITS, COST OF COVER OR OTHER SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT  DAMAGES ARISING FROM THE USE OF THE 3-D MODELS OR CORRESPONDING DOCUMENTATION, HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY.  THIS LIMITATION WILL APPLY EVEN IF CAB HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Some states do not allow the limitation or exclusion of liability for incidental, or consequential damages, so the above limitation may not apply to you.
If this agreement is translated into any other language than German, the German version remains the authoritative version.
If any of the afore mentioned provisions should be or become ineffective, this does not affect the validity of the remaining provisions. The ineffective or invalid provision shall be replaced by the corresponding statutory ruling, unless the parties reach legally effective agreement on another solution. The same also applies to any loopholes in the contract.

Accept license

3D CAD模型

此檔案是以STEP格式提供，所以必須是以CAD軟體開啟。下載免費檢視軟體STP viewer請連結 VariCAD Viewer (外部網站). 下載CAD模型請先註冊。 cab會根據隱私使用條款建立您的個人資料。您的個人資料將不會移轉給第三人作為其他用途使用。此目錄仍在持續建構中，我們將會提供更多的模型可供下載。

讀取PDF檔案前請先下載Adobe Reader。部分文件需要版本7或是更高版本才可讀取。請於此下載Adobe Reader

cab 非常樂意在任何時候、任何地點為您解答任何疑問：

條碼印表機 SQUIX 專用貼標手臂

現在就提出免費及非強制性購買的詢價需求：

詢問更多訊息

更多資訊：

參閱產品目錄(PDF)

Passwort vergessen?

快速連結

快速連結

SQUIX 貼標手臂
可建置於生產線上

貼標手臂 S1000

貼標手臂 S3200

滾貼模組 S5104, S5106

貼標手臂 S1000

手冊文件

產品目錄

註冊是必要的

3D CAD模型

Headquarters

Sales Office Asia

Sales Offices China

關於cab在推特

Choose your Language

Passwort vergessen?

快速連結

快速連結

SQUIX 貼標手臂 可建置於生產線上

貼標手臂 S1000

貼標手臂 S3200

滾貼模組 S5104, S5106

貼標手臂 S1000

手冊文件

產品目錄

註冊是必要的

3D CAD模型

Headquarters

Sales Office Asia

Sales Offices China

關於cab在推特

Choose your Language

SQUIX 貼標手臂
可建置於生產線上