Accessories for Label printer A8+
-
Extras
-
Reflective label sensor
From top
-
Adapter 100 mm diameter
To keep the bending to a minimum during stacking it is recommended to use a large core diameter.
-
Memory Card
CompactFlash Type I
-
External operation panel
If the operation panel is not accessible, after printer installation within a facility, an external one can be connected. Additional slots are available for CompactFlash memory card Type I and host interface.
-
Pause adapter PS7
Basic version: typical | Dispensing version A2+, A4+, A6+: possible
For printing in a label loop. Print job is stopped by the pause signal, with the label being printed finished first.
I/O Interface
Inputs: Pause, external error
Outputs: no print job, printer not ready, print job active
-
-
Interfaces
-
RS422 / RS485
1,200 to 230,400 baud/8 bit
-
Label selection – I/O box
Up to 16 different labels per box can be selected from the memory card.
-
WLAN 802.11b/g
Only few cards left in stock. After the remainder has been sold out, no repeat orders are possible.
-
-
Connecting cables
-
Connecting cable RS232-C
9/9 pin, length 3 m
-
-
Cutting, perforating, stacking labels
-
Cutter CU
Cutter CU
Used to cut paper labels, self-adhesive labels, cardboard, textile or synthetic materials as well as heat shrink tubes.Cutter CU4 CU6 CU8 Usage XD4T, XC4 XC6 A8+ Material width up to mm 110 180 232 Material weight cardbaord gr / m2 60-300 Material thickness mm 0.05-0.8 Cutting length mm > 5 Gap height up to mm 2.5 Cuts/min. 100 Stop print job When final position of cutter is not reached
-
-
Rewinding, unwinding labels
-
External rewinders ER4/6/8 with built-in power supply
To be used also with external printers. Label winding outside or inside.
External rewinder ER4/210 ER4/300 ER6/300 ER8/300 To be used with XD4T, XC4 XD4T, XC4 XC6 A8+ Material width up to mm 120 120 180 235 Roll diameter up to mm 205 300 300 300 Tightening axle for core diameter mm 76 Winding outside or inside Power supply 100–240 V ~ 50/60 Hz Adapter kit for 6.3 ER8 with A8+ 6.4 ER4, ER6 with XC4, XC6 -
External unwinders EU8
The external unwinder EU8 enables consistent label feed with heavy rolls. Outside and inside wound rolls can be processed.
External unwinder EU8/300 To be used with A8+ Material width up to mm 235 Roll diameter up to mm 300 Core diameter mm
with adapter mm40
76Winding outside or inside Adapter kit for 6.3 EU8 with A8+
-
-
Software
-
Label software cablabel S3
In cablabel S3 cab concentrates label design, print control and monitoring of all cab marking systems and synchronizes the development of devices and software.
-
Database Connector
In the stand-alone mode with additional network connection, the Database Connector enables printers to access data directly from a central ODBC-, OLEDB compatible database and to print it as a label.
-
Administration Network Manager
The cab Network Manager enables the user to control a number of printers across a network simultaneously. It supports monitoring, configuration, firmware updates, memory card administration, file synchronization and PIN administration centrally.
-
Programmer's guide
A general programmer's guide explaining and describing commands for different printer models via direct programming.
Programming Manual
Programming Manual A+ Series, XD4T, MACH4, PX and all printing systems based on the cab „X2“ board
-